Mr-Glass Custom & Geometric Windows Nationwide | Sightline Windows & Doors Sunrise

Mr-Glass Custom & Geometric Windows in Sunrise: What to Know First

We install and replace Mr-Glass custom and geometric windows in Sunrise as an independent Mr-Glass service provider, with most measured surveys completed within 48 hours of your call and written pricing delivered before any work begins. A typical custom geometric installation runs three to five weeks from signed quote to final inspection, depending on glass tempering lead times and Broward County permit scheduling. We do not quote over the phone; Haven Clause 1 requires that the measurement and the price live on the same document you keep.

Call (754) 254-5294

This page is for Sunrise homeowners who already own Mr-Glass products and need arched, curved, oversized, or otherwise non-rectangular openings addressed, or who are comparing Mr-Glass against other custom lines for a new installation. If you’re in the Inverrary area, Sawgrass Estates, or the newer construction west of Flamingo Road, you’ve likely seen our crews working. Call (754) 254-5294 to schedule your measured survey.

How Mr-Glass Products Fail - and How We Fix Them

• Series 5500 fixed geometric units with seal decompression. The argon-filled insulated glass units in the 5500 series use a dual-seal system where the secondary PIB seal can relax under repeated thermal cycling. In Sunrise, where afternoon attic temperatures above the window exceed 140°F for months, we see accelerated seal failure presenting as interior fogging that clears by morning. We replace with OEM-spec warm-edge spacers and re-gasket the frame pocket to reduce conductive heat transfer at the edge.
• Custom radius tops with substrate swell in the 7700 series. The 7700 series uses a pultruded fiberglass composite that performs well under load but can exhibit micro-fracturing at the radius transition when the interior wood substrate takes on moisture from failed exterior sealant. We remove the unit, dry the substrate with controlled airflow, and re-bed with backer rod and neutral-cure silicone rather than the original butyl, which gives better joint movement accommodation in Broward’s wet season.
• Oversized 8800 series impact units with sill pan drainage failure. The 8800 series impact-rated custom shapes require a sloped sill pan with weep drainage; in Sunrise homes built 2015-2019, we find pans installed dead-level or with weep holes caulked shut by painters. Water pools behind the interior stop and rots the jack studs. We re-pitch the pan, install insect-resistant weep covers, and document the slope with a photo in your job record.
• Geometric casements with hinge-side sag in the 6600 series. The 6600 casement line uses a concealed hinge system rated for 36-inch wide units, but custom trapezoids and triangles often run wider at the base. Hinge-side sag shows up as weatherstrip compression at the top and daylight at the sill. We specify heavy-duty hinge upgrades from the Mr-Glass commercial catalog, not the residential default, and shim the frame square before the unit goes in. Measure it right once, and the install tells you nothing went wrong.
• Custom low-E coatings with orientation-specific solar heat gain coefficient mismatch. Mr-Glass offers Cardinal 366 and LoE-180 coatings specified by facade orientation, but we’ve found Sunrise homes where west-facing geometric units received south-specified glass. The result is afternoon heat gain that overwhelms the HVAC. We pull the glazing schedule, verify SHGC and U-factor against the original permit, and re-specify if the glass doesn’t match the orientation.

Our Mr-Glass Custom & Geometric Windows Process

1. 1
   Measured survey. Sonia Raman or a licensed technician arrives with a laser measure, level, and the printed Mr-Glass sizing catalog. We record rough opening dimensions, plumb, level, and square to 1/16 inch, note any structural repair needs, and photograph the existing unit and surrounding wall condition. You keep a copy of the survey.
2. 2
   Glazing specification. We determine whether OEM Mr-Glass parts are available for your series and year, or whether a quality aftermarket equivalent meets the original performance spec. For discontinued custom profiles, we fabricate from extrusion drawings and submit samples for your approval.
3. 3
   Written quote. The quote references the survey document number, lists every material by manufacturer and model, names labor hours, and states the total. Haven Clause 1: this price does not change unless you change the scope.
4. 4
   Permit and order. For impact-rated custom work in Sunrise, we pull the permit, submit the Miami-Dade or Florida Product Approval documentation for your specific Mr-Glass configuration, and order glass with tempering and any required laminations.
5. 5
   Installation and testing. We set the unit with proper shimming, sealant backer rod, and mechanical fastening per the engineer’s detail, then test operable units for torque, verify fixed units for deflection, and confirm drainage paths are clear.
6. 6
   Documentation and closeout. You receive the photo record, the final invoice matching the quote, the 365-Day Done Right Promise under the Haven Standard, and the permit sign-off. Evidence on every job, Haven Clause 4.

Before

After

What Mr-Glass Custom & Geometric Windows Costs in Sunrise

These ranges reflect Sunrise labor rates, Broward County permit fees, and typical access conditions. Second-story installations with interior plaster or tile protection add labor. We do not estimate until we measure. Call (754) 254-5294 for your free measured survey and written quote.

Why Sunrise Homeowners Call Sightline Windows & Doors Sunrise for Mr-Glass Work

We’ve installed and serviced Mr-Glass products in Sunrise since 2012, and we also specify PGT, CGI, CWS, and ES Windows when the opening or the budget points elsewhere. That multi-brand fluency means we diagnose against the product, not our inventory. Every technician is background-checked, uniformed, and identified by license number before arrival, Haven Clause 3. The 365-Day Done Right Promise is stamped on every job, not offered as a courtesy. Calls are answered by a live person, 24/7. And the written price you receive is the price on the final invoice, because Haven Clause 1 leaves no room for change orders.

FAQs